All projects
Featured projects and work developed in electronics, robotics, software and embedded systems.











Chez Novadem, development of a test bench modular test bench to automate validation of the NX70 drone's electronic boards.

Design as a team of a autonomous robot with holonomic movement, vision, LiDAR and manipulation.
Personal platform developed from the definition of performances au firmware ESP32 and au PCB KiCad.

Analyse of the protocol USB HID and development of a tool Python Linux for piloter un Aaronia BPSG 6.
Featured projects and work developed in electronics, robotics, software and embedded systems.










Durant un stage de huit semaines chez Novadem, I developed un test bench designed to automate validation of the drone NX70. The goal was to reduce testing time and improve diagnosis reliability.
Architecture of the test bench
I also analyzed requirements with production engineers and contributed to hardware improvements aimed at making the measurements.
Skills: C++ · Automated tests · Software architecture · Interface graphique · Embedded systems · Instrumentation
Within a a team de five people of the Robot Club Toulon, I contributed to the design of an autonomous robot for the Eurobot 2025 competition. The robot had to manipulate of elements, move autonomously and interact with the other robots.
Robot Eurobot 2025
Robot built by the team
The software part was based on an existing codebase of the club, adapted to the new architecture and aux nouveaux sensors. This project m'a permis de travailler on l'integration de several subsystems softwares and hardware in un system robotics complex.
Skills: C/C++ · Robotics · Embedded systems · Sensors · Actuators · Vision · LiDAR · Integration
After taking part in an inter-BUT robotics competition in Paris in 2024, I developed alone a new platform designed to improve trajectory tracking performance and serve as serve as an educational platform.
Design of the plateforme under KiCad
Skills: C/C++ · ESP32 · PD control · Robotics · Bluetooth · Wi-Fi · KiCad · PCB
As part of a second-year BUT GEII project, I completed with a partner the reverse engineering of the protocol USB of a generator de signals RF Aaronia BPSG 6, couvrant 23,5 MHz to 6 GHz.
RF signal generator Aaronia BPSG 6
Architecture of the solution
The Python solution generates the registers of the PLL, builds the frames USB and controls la frequency on the full range 23,5 MHz - 6 GHz with a resolution below 1 Hz. It runs on Linux/ARM, including on Raspberry Pi, en headless mode. Le controls of the gain could not be fully determined.
Skills: Python · Linux · USB HID · Wireshark · Reverse Engineering · Protocoles · RF
Project completed during the second year of BUT GEII about the design of a complete home automation system. The system controls actuators from a touchscreen or a web interface and collects measurements de several sensors.
Home automation board designed under KiCad
Functional prototype
Skills: C++ · ESP32 · Embedded web · Wi-Fi · KiCad · PCB
Development of a autonomous robot utilisant un microcontroller PIC and a architecture softwarele adapted to real-time constraints.
Autonomous obstacle-avoidance robot
Skills: C · C# · PIC · Real-time · PWM · Interrupts · CAN · SPI · I2C · UART
Setup of a self-hosted server on Raspberry Pi 5 to host un personal website and various services.
Serveur personnel on Raspberry Pi
Skills: Linux · Apache · HTML · CSS · JavaScript · Networking · Security
Development of a compact lighting controller based on Arduino. The embedded software manages several operating modes using state machines.
Board SmartLight
Prototype SmartLight
Skills: C++ · Arduino · State machines · PWM · Interrupts · Timers · KiCad
Design as a team of a system transmitter/receiver audio permettant de transmettre a control remotely via a specific audio frequency.
Prototype of the transmitter
Prototype final
Sizing of active filters was validated with a validation through simulation SPICE.
Skills: Electronics analog · SPICE · Filters active · Traitement of the signal
Development as a team of a stopwatch digital VHDL on FPGA Nexys A7.
Board FPGA Nexys A7
Skills: VHDL · FPGA · Nexys A7 · Testbench · Logique digital
Design as a team d'a pedal de compression analog for guitar electric.
Functional diagram
Electronic schematic
LTspice simulation
Skills: Electronics analog · LTspice · Signal processing · KiCad · PCB
Ongoing personal project: design of a Bluetooth speaker with a three-way audio architecture.
Design of the enceinte under KiCad
The project includes the study and simulation of active filters, as well as PCB design with separation of analog and digital sections.
Skills: Audio electronics · Bluetooth · Class D · Active filters · KiCad · PCB
Complete team renovation of a sailboat SIR 530 damaged and abandoned.
Sailboat SIR 530
This project also allowed me de travailler on la planning, la task allocation, la budget management and le teamwork on several month.